added unset/hops command

[spider.git] / cmd / Commands_en.hlp

diff --git a/cmd/Commands_en.hlp b/cmd/Commands_en.hlp
index 09c69df3fe17889de282443e2aefd635c0bf8926..d04f9fa8bfb2ed9dec77d0fe14792ef3afa8e7ff 100644 (file)
--- a/cmd/Commands_en.hlp
+++ b/cmd/Commands_en.hlp
@@ -1192,8 +1192,8 @@ You can show what levels you are logging with SHOW/DEBUG
 === 0^SET/DX^Allow DX messages to come out on your terminal
 === 0^UNSET/DX^Stop DX messages coming out on your terminal
 
-=== 0^SET/DXGRID^Allow Grid Squares on the end of DX announcements
-=== 0^UNSET/DXGRID^Stop Grid Squares on the end of DX announcements
+=== 0^SET/DXGRID^Allow QRA Grid Squares on the end of DX announcements
+=== 0^UNSET/DXGRID^Stop QRA Grid Squares on the end of DX announcements
 A standard feature which is enabled in version 1.43 and above is 
 that if the spotter's grid square is known it is output on the end
 of a DX announcement (there is just enough room). Some user programs
@@ -1213,6 +1213,21 @@ The setting is stored in your user profile.
 
 YOU DO NOT NEED TO USE THIS COMMAND IF YOU ARE CONNECTED VIA AX25.
 
+=== 0^SET/EMAIL <email> ...^Set email address(es) and forward your personals
+=== 0^UNSET/EMAIL^Stop personal msgs being forwarded by email
+If any personal messages come in for your callsign then you can use
+these commands to control whether they are forwarded onto your email
+address. To enable the forwarding do something like:-
+
+  SET/EMAIL mike.tubby@somewhere.com
+
+You can have more than one email address (each one separated by a space).
+Emails are forwarded to all the email addresses you specify.
+
+You can disable forwarding by:-
+
+  UNSET/EMAIL
+
 === 0^SET/HERE^Tell the system you are present at your terminal
 === 0^UNSET/HERE^Tell the system you are absent from your terminal
 
@@ -1223,6 +1238,7 @@ eg:-
   SET/HOMENODE gb7djk
 
 === 8^SET/HOPS <call> ann|spots|route|wwv|wcy <n>^Set hop count  
+=== 8^UNSET/HOPS <call> ann|spots|route|wwv|wcy^Unset hop count  
 Set the hop count for a particular type of broadcast for a node.
 
 This command allows you to set up special hop counts for a node 
@@ -1235,6 +1251,12 @@ eg:
 Set SHOW/HOPS for information on what is already set. This command
 creates a filter and works in conjunction with the filter system. 
 
+You can unset the hops with command UNSET/HOPS. For example:-
+
+  unset/hops gb7djk ann
+  unset/hops gb7mbc spots
+
+
 === 9^SET/ISOLATE^Isolate a node from the rest of the network
 Connect a node to your system in such a way that you are a full protocol
 member of its network and can see all spots on it, but nothing either leaks
@@ -1382,8 +1404,8 @@ password for a user.
 Tell the system that the call(s) are to be treated as DXSpider node and
 fed new style DX Protocol rather normal user commands.
 
-=== 9^SET/SYS_QRA <locator>^Set your cluster QRA locator
-=== 0^SET/QRA <locator>^Set your QRA locator
+=== 9^SET/SYS_QRA <locator>^Set your cluster QRA Grid locator
+=== 0^SET/QRA <locator>^Set your QRA Grid locator
 Tell the system what your QRA (or Maidenhead) locator is. If you have not
 done a SET/LOCATION then your latitude and longitude will be set roughly
 correctly (assuming your locator is correct ;-). For example:-
@@ -1689,8 +1711,8 @@ See also SHOW/DXCC
 Show the name and location where every program module was load from. This
 is useful for checking where you think you have loaded a .pm file from. 
 
-=== 0^SHOW/QRA <locator> [<locator>]^Show distance between locators
-=== 0^SHOW/QRA <lat> <long>^Convert latitude and longitude to a locator
+=== 0^SHOW/QRA <locator> [<locator>]^Show distance between QRA Grid locators
+=== 0^SHOW/QRA <lat> <long>^Convert lat/long to a QRA Grid locator
 This is a multipurpose command that allows you either to calculate the
 distance and bearing between two locators or (if only one locator is
 given on the command line) the distance and beraing from your station