# Comment lines are indented before printing
#
=== 0^ANNOUNCE <text>^Send an announcement to LOCAL users only
+<text> is the text of the announcement you wish to broadcast
=== 0^ANNOUNCE FULL <text>^Send an announcement cluster wide
This will send your announcement cluster wide
=== 5^ANNOUNCE SYSOP <text>^Send an announcement to Sysops only
-=== 0^ANNOUNCE-
-<text> is the text of the announcement you wish to broadcast
-
=== 0^APROPOS <string>^Search help database for <string>
Search the help database for <string> (it isn't case sensitive), and print
the names of all the commands that may be relevant.
be ALL the non-private messages. You can prevent this by using these
commmands:-
- catch GB7DJK all
- catch GB7DJK 300 301 302 303
+ catch GB7DJK all
+ catch GB7DJK 300 301 302 303
and to undo what you have just done:-
-
- uncatch GB7DJK all
- uncatch GB7DJK 300 301 302 303
+
+ uncatch GB7DJK all
+ uncatch GB7DJK 300 301 302 303
which will arrange for them to be forward candidates again.
+=== 0^DBAVAIL^Show a list of all the Databases in the system
+Title says it all really, this command lists all the databases defined
+in the system. It is also aliased to SHOW/COMMAND.
+
+=== 9^DBCREATE <name>^Create a database entry
+=== 9^DBCREATE <name> chain <name> [<name>..]^Create a chained database entry
+=== 9^DBCREATE <name> remote <node>^Create a remote database entry
+DBCREATE allows you to define a database in the system. It doesn't actually
+create anything, just defines it.
+
+The databases that are created are simple DB_File hash databases, they are
+therefore already 'indexed'.
+
+You can define a local database with the first form of the command eg:
+
+ DBCREATE oblast
+
+You can also chain databases with the addition of the 'chain' keyword.
+This will search each database one after the other. A typical example
+is:
+
+ DBCREATE sdx_qsl chain sql_ad
+
+No checking is done to see if the any of the chained databases exist, in
+fact it is usually better to do the above staement first then do each of
+the chained databases.
+
+Databases can exist offsite. To define a database that lives on another
+node do:
+
+ DBCREATE buckmaster remote gb7dxc
+
+Remote databases cannot be chained; however, the last database in a
+a chain can be a remote database eg:
+
+ DBCREATE qsl chain gb7dxc
+
+To see what databases have been defined do:
+
+ DBAVAIL (or it will have been aliased to SHOW/COMMAND)
+
+It would be normal for you to add an entry into your local Aliases file
+to allow people to use the 'SHOW/<dbname>' style syntax. So you would
+need to add a line like:-
+
+ 's' => [
+ ..
+ ..
+ '^sh\w*/buc', 'dbshow buckmaster', 'dbshow',
+ ..
+ ..
+ ],
+
+to allow
+
+ SH/BUCK g1tlh
+
+to work as they may be used to.
+
+See DBIMPORT for the importing of existing AK1A format data to databases.
+See DBSHOW for generic database enquiry
+
+=== 9^DBIMPORT <dbname> <filename>^Import AK1A data into a database
+If you want to import or update data in bulk to a database you can use
+this command. It will either create or update entries into an existing
+database. For example:-
+
+ DBIMPORT oblast /tmp/OBLAST.FUL
+
+will import the standard OBLAST database that comes with AK1A into the
+oblast database held locally.
+
+=== 9^DBREMOVE <dbname>^Delete a database
+DBREMOVE will completely remove a database entry and also delete any data
+file that is associated with it.
+
+There is no warning, no comeback, no safety net.
+
+For example:
+
+ DBREMOVE oblast
+
+will remove the oblast database from the system and it will also remove
+the associated datafile.
+
+I repeat:
+
+There is no warning, no comeback, no safety net.
+
+You have been warned.
+
+=== 0^DBSHOW <dbname> <key>^Display an entry, if it exists, in a database
+This is the generic user interface to the database to the database system.
+It is expected that the sysop will add an entry to the local Aliases file
+so that users can use the more familiar AK1A style of enquiry such as:
+
+ SH/BUCK G1TLH
+
+but if he hasn't and the database really does exist (use DBAVAIL or
+SHOW/COMMAND to find out) you can do the same thing with:
+
+ DBSHOW buck G1TLH
+
=== 9^DEBUG^Set the cluster program into debug mode
Executing this command will only have an effect if you are running the cluster
in debug mode i.e.
=== 5^READ-^
As a sysop you may read any message on the system
-=== 0^REPLY^Reply to the last message that you have read
-=== 0^REPLY <msgno>^Reply to the specified message
-=== 0^REPLY PRIVATE <msgno>^Reply privately to the specified message
+=== 0^REPLY^Reply (privately) to the last message that you have read
+=== 0^REPLY <msgno>^Reply (privately) to the specified message
+=== 0^REPLY B <msgno>^Reply as a Bulletin to the specified message
+=== 0^REPLY NOPrivate <msgno>^Reply as a Bulletin to the specified message
=== 0^REPLY RR <msgno>^Reply to the specified message with read receipt
You can reply to a message and the subject will automatically have
"Re:" inserted in front of it, if it isn't already present.
You can also use all the extra qualifiers such as RR, PRIVATE,
-NOPRIVATE that you can use with the SEND command (see SEND
+NOPRIVATE, B that you can use with the SEND command (see SEND
for further details)
=== 0^SEND <call> [<call> ...]^Send a message to one or more callsigns
spaces - but they won't appear in the password). You can see the
result with STAT/USER.
-=== 0^SET/QRA <locator>^Set your QRA locator
=== 9^SET/SYS_QRA <locator>^Set your cluster QRA locator
+=== 0^SET/QRA <locator>^Set your QRA locator
Tell the system what your QRA (or Maidenhead) locator is. If you have not
done a SET/LOCATION then your latitude and longitude will be set roughly
correctly (assuming your locator is correct ;-). For example:-
See also TYPE - to see the contents of a file.
+=== 0^SHOW/MUF <prefix> [<hours>][long]^Show the likely propagation to a prefix
+This command allow you to estimate the likelihood of you contacting
+a station with the prefix you have specified. The output assumes a modest
+power of 20dBW and receiver sensitivity of -123dBm (about 0.15muV/10dB SINAD)
+
+The result predicts the most likely operating frequencies and signal
+levels for high frequency (shortwave) radio propagation paths on
+specified days of the year and hours of the day. It is most useful for
+paths between 250 km and 6000 km, but can be used with reduced accuracy
+for paths shorter or longer than this.
+
+The command uses a routine MINIMUF 3.5 developed by the U.S. Navy and
+used to predict the MUF given the predicted flux, day of the year,
+hour of the day and geographic coordinates of the transmitter and
+receiver. This routine is reasonably accurate for the purposes here,
+with a claimed RMS error of 3.8 MHz, but much smaller and less complex
+than the programs used by major shortwave broadcasting organizations,
+such as the Voice of America.
+
+The command will display some header information detailing its
+assumptions, together with the locations, latitude and longitudes and
+bearings. It will then show UTC (UT), local time at the other end
+(LT), calculate the MUFs, Sun zenith angle at the midpoint of the path
+(Zen) and the likely signal strengths. Then for each frequency for which
+the system thinks there is a likelihood of a circuit it prints a value.
+
+The value is currently a likely S meter reading based on the conventional
+6dB / S point scale. If the value has a '+' appended it means that it is
+1/2 an S point stronger. If the value is preceeded by an 'm' it means that
+there is likely to be much fading and by an 's' that the signal is likely
+to be noisy.
+
+By default SHOW/MUF will show the next two hours worth of data. You
+can specify anything up to 24 hours worth of data by appending the no of
+hours required after the prefix. For example:-
+
+ SH/MUF W
+
+produces:
+
+ RxSens: -123 dBM SFI: 159 R: 193 Month: 10 Day: 21
+ Power : 20 dBW Distance: 6283 km Delay: 22.4 ms
+ Location Lat / Long Azim
+ East Dereham, Norfolk 52 41 N 0 57 E 47
+ United-States-W 43 0 N 87 54 W 299
+ UT LT MUF Zen 1.8 3.5 7.0 10.1 14.0 18.1 21.0 24.9 28.0 50.0
+ 18 23 11.5 -35 mS0+ mS2 S3
+ 19 0 11.2 -41 mS0+ mS2 S3
+
+indicating that you will have weak, fading circuits on top band and
+80m but usable signals on 40m (about S3).
+
+inputing:-
+
+ SH/MUF W 24
+
+will get you the above display, but with the next 24 hours worth of
+propagation data.
+
+ SH/MUF W L 24
+ SH/MUF W 24 Long
+
+Gives you an estimate of the long path propagation characterics. It
+should be noted that the figures will probably not be very useful, nor
+terrible accurate, but it is included for completeness.
+
=== 0^SHOW/PREFIX <callsign>^Interrogate the prefix database
This command takes the <callsign> (which can be a full or partial
callsign or a prefix), looks up which internal country number
See also SHOW/DXCC
-=== 0^SHOW/PROGRAM^Show the locations of all the included program modules
+=== 0^SHOW/SUN [<callsign>|<prefix>]^Display sunrise and sunset times
+Show the sunrise and sunset times for a callsign (if it is known to the
+cluster), a prefix or, if nothing is specified, at your QTH (if you have
+remembered to set your location using SET/LOCATION or SET/QRA). If all else
+fails it will show the sunrise and set times for the node that you are
+connected to.
+
+You can enter more than one prefix or callsign:-
+
+ SH/SUN G1TLH G8TIC W9
+
+=== 5^SHOW/PROGRAM^Show the locations of all the included program modules
Show the name and location where every program module was load from. This
is useful for checking where you think you have loaded a .pm file from.
=== 5^SHUTDOWN^Shutdown the cluster
Shutdown the cluster and disconnect all the users
+=== 5^STAT/DB <dbname>^Show the status of a database
+Show the internal status of a database descriptor.
+
+Depending on your privilege level you will see more or less information.
+This command is unlikely to be of much use to anyone other than a sysop.
+
=== 5^STAT/CHANNEL [<callsign>]^Show the status of a channel on the cluster
Show the internal status of the channel object either for the channel that
you are on or else for the callsign that you asked for.
Only the fields that are defined (in perl term) will be displayed.
+=== 5^STAT/MSG <msgno>^Show the status of a message
+This command shows the internal status of a message and includes information
+such as to whom it has been forwarded, its size, origin etc etc.
+
=== 5^STAT/USER [<callsign>]^Show the full status of a user
Shows the full contents of a user record including all the secret flags
and stuff.
with others to obscure your reply for any watchers. For example (and
these values are for explanation :-):
-password = 012345678901234567890123456789
- > sysop
-22 10 15 17 3
+ password = 012345678901234567890123456789
+ > sysop
+ 22 10 15 17 3
you type:-
-aa2bbbb0ccc5ddd7xxx3n
-or 2 0 5 7 3
-or 20573
+ aa2bbbb0ccc5ddd7xxx3n
+ or 2 0 5 7 3
+ or 20573
They will all match. If there is no password you will still be offered
numbers but nothing will happen when you input a string. Any match is
=== 5^WX SYSOP <text>^Send a weather message to other clusters only
Weather messages can sometimes be useful if you are experiencing an extreme
that may indicate enhanced conditions
+
projects / spider.git / blobdiff