Best of luck - you will need it.
+=== 9^DEMONSTRATE <call> <command>^Demonstrate a command to another user
+This command is provided so that sysops can demonstrate commands to
+other users. It runs a command as though that user had typed it in and
+then sends the output to that user, together with the command that
+caused it.
+
+ DEMO g7brn sh/dx iota oc209
+ DEMO g1tlh set/here
+
+Note that this command is similar to SPOOF and will have the same side
+effects. Commands are run at the privilege of the user which is being
+demonstrated to.
+
=== 0^KILL <msgno> [<msgno..]^Delete a message from the local system
=== 0^KILL <from msgno>-<to msgno>^Delete a range of messages
=== 0^KILL from <regex>^Delete messages FROM a callsign or pattern
set/badspotter VE2STN
-will stop anything from VE2STN. If you want SSIDs as well then you must
-enter them specifically.
+will stop anything from VE2STN. This command will automatically
+stop spots from this user, regardless of whether or which SSID
+he uses. DO NOT USE SSIDs in the callsign, just use the callsign
+as above or below.
unset/badspotter VE2STN
=== 0^SHOW/HFSTATS^Show the HF DX Statistics for last 31 days
Show the HF DX spots breakdown by band for the last 31 days
-=== 0^SHOW/HFTABLE^Show the HF DX Spotter Table for your country
-Show the HF DX Spotter table for your country for the last 31 days
+=== 0^SHOW/HFTABLE [prefix ...]^Show the HF DX Spotter Table
+Show the HF DX Spotter table for the list of prefixes for the last 31 days,
+if there are no prefixes then it will show the table for your country.
+
+Remember that some countries have more than one "DXCC country" in them
+(eg G :-), to show them (assuming you are not in G already which is
+specially treated in the code) you must list all the relevant prefixes
+
+ sh/hftable g gm gd gi gj gw gu
+
+Note that the prefixes are converted into country codes so you don't have
+to list all possible prefixes for each country.
=== 8^SHOW/HOPS <call> [ann|spots|route|wcy|wwv]^Show the hop counts for a node
This command shows the hop counts set up for a node. You can specify
=== 0^SHOW/VHFSTATS^Show the VHF DX Statistics for last 31 days
Show the VHF DX spots breakdown by band for the last 31 days
-=== 0^SHOW/VHFTABLE^Show the VHF DX Spotter Table for your country
-Show the VHF DX Spotter table for your country for the last 31 days
+=== 0^SHOW/VHFTABLE [prefix ...]^Show the VHF DX Spotter Table
+Show the VHF DX Spotter table for the list of prefixes for the last 31 days,
+if there are no prefixes then it will show the table for your country.
+
+Remember that some countries have more than one "DXCC country" in them
+(eg G :-), to show them (assuming you are not in G already which is
+specially treated in the code) you must list all the relevant prefixes
+
+ sh/vhftable g gm gd gi gj gw gu
+
+Note that the prefixes are converted into country codes so you don't have
+to list all possible prefixes for each country.
=== 0^SHOW/WCY^Show last 10 WCY broadcasts
=== 0^SHOW/WCY <n>^Show last <n> WCY broadcasts